N4534G Robinson Helicopter R44 accident

NTSB GAA17CA151 · 2017-02-14 · Holtville, CA

Docket — crew, injuries and powerplant

Summary

The pilot in the skid-equipped helicopter reported that he had performed an agricultural application flight. The helicopter was within 100 lbs of the maximum gross weight at the time of the accident. The helicopter was headed south, and the pilot made a left turn to the west, and the helicopter began to settle with power. The pilot noticed the low rotor rpm, and the helicopter touched down on the soft dirt surface and rolled over. The helicopter sustained substantial damage to both rotor drive systems and the fuselage and tailboom. In an interview with National Transportation Safety Board investigator-in-charge, the pilot stated that the helicopter was about 20 ft above ground level when he noticed the low rotor rpm horn and that the airspeed was about 20 knots. He recalled that, when he made the left turn, he was operating with a tailwind. He added that the design of the hopper was not approved by the Federal Aviation Administration to be jettisoned. The pilot reported that there were no preaccident mechanical malfunctions or failures with the helicopter that would have precluded normal operation. Additional Information According to the Federal Aviation Administration (FAA) Helicopter Flying Handbook FAA-8083-21A (HFH) (pg. 2-4, para. 5), turns in a helicopter increase the load factor exponentially, ultimately increasing the power requirement that is necessary to maintain the helicopter's altitude. Left pedal turns increase the quantity of anti-torque produced by the tail rotor, by demanding additional power from the 260-brake horsepower engine. Pilot flight control inputs demanding more power than the engine is capable of producing, with respect to the atmospheric conditions, adversely affects the helicopters ability to sustain its altitude. Available engine power is directly correlated to main and tail rotor RPM. FAA-8083-21A (pg. 7-2, para. 5), "Factors Affecting Performance," stated: The wind direction is also an important consideration. Headwinds are the most desirable as they contribute to the greatest increase in performance. Strong crosswinds and tailwinds may require the use of more tail rotor thrust to maintain directional control. This increased tail rotor thrust absorbs power from the engine, which means there is less power available to the main rotor for the production of lift. FAA-8083-21A (pg. 2-4, para. 6), "Weight," stated: To overcome this additional load factor, the helicopter must be able to produce more lift. If excess engine power is not available, the helicopter either descends or has to decelerate in order to maintain the same altitude. The load factor and, hence, apparent gross weight increase is relatively small in banks up to 30°. Even so, under the right set of adverse circumstances, such as high DA, turbulent air, high gross weight, and poor pilot technique, sufficient or excess power may not be available to maintain altitude and airspeed. FAA-8083-21A (pg. 2-5, para. 1), "Weight," further stated: Regardless of how much weight one can carry or the engine power that it may have, they (helicopters) are all susceptible to aerodynamic overloading. Unfortunately, if the pilot attempts to push the performance envelope the consequence can be fatal. Aerodynamic forces effect every movement in a helicopter, whether it is increasing the collective or a steep bank angle. Anticipating results from a particular maneuver or adjustment of a flight control is not good piloting technique. Instead pilots need to truly understand the capabilities of the helicopter under any and all circumstances and plan to never exceed the flight envelope for any situation.

Full narrative

The pilot in the skid-equipped helicopter reported that he had performed an aerial application flight. The helicopter was within 100 pounds of the maximum gross weight at the time of the accident. The helicopter was headed south and the pilot made a left turn to the west and began to settle with power. The pilot noticed the low rotor revolutions per minute (RPM) and the helicopter touched down on the soft dirt surface and rolled over. The helicopter sustained substantial damage to both rotor drive systems, fuselage and tailboom.

In an interview with National Transportation Safety Board investigator-in-charge the pilot stated that the helicopter was about 20 feet above ground level when he noticed the low rotor RPM horn and the airspeed was about 20 knots. He recalled that when he made the left turn, he was operating with a tailwind. He added that the design of the hopper was not approved by the Federal Aviation Administration to be jettisoned.

The pilot reported that there were no preaccident mechanical malfunctions or failures with the helicopter that would have precluded normal operation.

Additional Information

According to the Federal Aviation Administration (FAA) Helicopter Flying Handbook FAA-8083-21A (HFH) (pg. 2-4, para. 5), turns in a helicopter increase the load factor exponentially, ultimately increasing the power requirement that is necessary to maintain the helicopter's altitude. Left pedal turns increase the quantity of anti-torque produced by the tail rotor, by demanding additional power from the 260-brake horsepower engine. Pilot flight control inputs demanding more power than the engine is capable of producing, with respect to the atmospheric conditions, adversely affects the helicopters ability to sustain its altitude. Available engine power is directly correlated to main and tail rotor RPM.

The FAA Helicopter Flying Handbook FAA-8083-21A (pg. 7-2, para. 5) per the section entitled Factors Affecting Performance:

The wind direction is also an important consideration. Headwinds are the most desirable as they contribute to the greatest increase in performance. Strong crosswinds and tailwinds may require the use of more tail rotor thrust to maintain directional control. This increased tail rotor thrust absorbs power from the engine, which means there is less power available to the main rotor for the production of lift.

The FAA Helicopter Flying Handbook FAA-8083-21A (pg. 2-4, para. 6) entitled Weight, asserts:

To overcome this additional load factor, the helicopter must be able to produce more lift. If excess engine power is not available, the helicopter either descends or has to decelerate in order to maintain the same altitude. The load factor and, hence, apparent gross weight increase is relatively small in banks up to 30°. Even so, under the right set of adverse circumstances, such as high DA, turbulent air, high gross weight, and poor pilot technique, sufficient or excess power may not be available to maintain altitude and airspeed.

The FAA Helicopter Flying Handbook FAA-8083-21A (pg. 2-5, para. 1) entitled Weight, further states:

Regardless of how much weight one can carry or the engine power that it may have, they (helicopters) are all susceptible to aerodynamic overloading. Unfortunately, if the pilot attempts to push the performance envelope the consequence can be fatal. Aerodynamic forces effect every movement in a helicopter, whether it is increasing the collective or a steep bank angle. Anticipating results from a particular maneuver or adjustment of a flight control is not good piloting technique. Instead pilots need to truly understand the capabilities of the helicopter under any and all circumstances and plan to never exceed the flight envelope for any situation.

Probable cause

The pilot’s initiation of a left turn at a low altitude with low airspeed and a tailwind while operating near maximum gross weight, which resulted in the helicopter losing altitude, touching down on a dirt surface, and a subsequent dynamic rollover. The National Transportation Safety Board determined the probable cause of this accident.

Circumstances

Event type
Accident
Highest injury
None
Weather conditions
Visual Meteorological Cond
Light condition
Night/Dark
Sky condition
NONE
Ceiling (ft)
0
Visibility (sm)
10
Wind direction
250
Wind speed (kt)
3
Temperature (F)
57
Distance from field
0.0

Aircraft

RegistrationMakeModelDamageFAR part
N4534G ROBINSON HELICOPTER R44 SUBS 137

Sequence of events

#OccurrencePhase
1 Maneuvering-low-alt flying Low altitude operation/event Climb
2 Maneuvering-low-alt flying Aerodynamic stall/spin defining Climb
3 Maneuvering-low-alt flying Collision with terr/obj (non-CFIT) Climb
4 Maneuvering-low-alt flying Off-field or emergency landing Climb

Findings

Finding
Personnel issues-Task performance-Use of equip/info-Aircraft control-Pilot cause
Personnel issues-Action/decision-Info processing/decision-Decision making/judgment-Pilot cause
Aircraft-Aircraft oper/perf/capability-Performance/control parameters-Altitude-Not attained/maintained cause
Aircraft-Aircraft oper/perf/capability-Performance/control parameters-Airspeed-Not attained/maintained cause
Aircraft-Aircraft oper/perf/capability-Performance/control parameters-Prop/rotor parameters-Not attained/maintained cause
Environmental issues-Conditions/weather/phenomena-Wind-Tailwind-Effect on equipment cause
Aircraft-Aircraft oper/perf/capability-Aircraft capability-Maximum weight-Related operating info factor
Environmental issues-Physical environment-Runway/land/takeoff/taxi surface-Soft surface-Effect on operation factor