N4031D accident

NTSB WPR20LA099 · 2020-03-05 · Moab, UT · near CNY

Docket — crew, injuries and powerplant

Summary

The pilot reported that he performed a normal three-point landing in the tailwheel-equipped airplane, and, during the landing roll, the airplane veered to the right. The pilot corrected by applying left rudder, and, shortly after, the airplane "pulled hard to the right." Despite the pilot's control inputs, the airplane exited the right side of the runway onto soft gravel and nosed over, which resulted in structural damage to the fuselage. The pilot added that he believed the right brake was “dragging significantly.” Postaccident examination of the airplane revealed that the right brake caliper brake line attachment fitting was bent outward, toward the wheel assembly, which allowed for a portion of the brake line attached to the fitting to contact the inner wheel assembly. Associated rub marks on the inboard wheel assembly were found, consistent with contact with the brake line sleeve while the wheel was not in motion, and likely resulted from the accident. No additional anomalies were noted with the right brake or wheel assembly. The accident is consistent with the pilot not maintaining directional control during landing.

Full narrative

On March 4, 2020, about 2315 mountain standard time, a Cessna 182A, N4031D, was substantially damaged when it was involved in an accident near Moab, Utah. The pilot was not injured. The airplane was operated as a Title 14 Code of Federal Regulations part 91 personal flight.

The pilot reported that he performed a normal three-point landing in the tailwheel-equipped airplane on runway 21 at night. During the landing roll, the airplane veered to the right, which the pilot corrected by applying left rudder. Shortly after, the airplane "pulled hard to the right" and, despite the pilot's control inputs, exited the right side of the runway onto soft gravel and nosed over. The pilot added that he believed the right brake was “dragging significantly.” Postaccident examination of the airplane revealed that the fuselage was substantially damaged. Additional examination revealed that the fitting, where the brake line attaches to the upper portion of the brake caliper, was slightly bent outward toward the wheel assembly, which allowed for a portion of the brake line attached to the fitting to contact the inner wheel assembly, as shown in figure 1.

Figure 1: View of the right main landing gear brake assembly.

An area of scratched/displaced paint (about 3/4 to 1 inch wide and 1/4 inch tall) was observed on the wheel assembly. No additional damage was noted on the inboard portion of the wheel assembly. Additional damage was observed on the inboard side of the brake line sleeve fitting, as shown in figure 2.

Figure 2: View of the right main landing gear brake assembly.

The brake caliper and rotor were found unremarkable. When the brake line was pulled away from the wheel assembly, the wheel rotated freely by hand and was not restricted. However, when the brake line was not pulled away from the wheel assembly, it contacted the wheel assembly and rotated slightly before it stopped. It could not be determined when the caliper fitting was bent.

Probable cause

The pilot’s failure to maintain directional control during landing, which resulted in a runway excursion and the airplane’s subsequent noseover. The National Transportation Safety Board determined the probable cause of this accident.

Circumstances

Event type
Accident
Highest injury
Minor
Weather conditions
Visual Meteorological Cond
Light condition
Night
Sky condition
NONE
Ceiling (ft)
0
Visibility (sm)
10
Wind direction
0
Temperature (F)
37
Nearest airport
Canyonlands
Distance from field
0.0
Airport elevation
4590

Aircraft

RegistrationMakeModelDamageFAR part
N4031D — — SUBS 091

Sequence of events

#OccurrencePhase
1 Landing-landing roll Loss of control on ground defining Cruise
2 Landing-landing roll Runway excursion Cruise
3 Landing-landing roll Nose over/nose down Cruise

Findings

Finding
Personnel issues-Task performance-Use of equip/info-Use of equip/system-Pilot factor
Aircraft-Aircraft oper/perf/capability-Performance/control parameters-Directional control-Not attained/maintained factor