N31PB Bell Helicopter Textron Canada 407 accident

NTSB ERA23LA319 · 2023-08-01 · North Charleston, SC · near CHS

Docket — crew, injuries and powerplant

Summary

The pilot reported that, about 35 minutes into the flight, he noticed that the helicopter began to yaw to the right and his pedal inputs did not correct the situation. He contacted the tower at his destination and declared an emergency. As he approached the runway for a straight-in landing, the helicopter yawed again. He lowered the collective, but the helicopter continued to yaw right. He then reduced the throttle and attempted to maintain a level attitude. The helicopter struck the ground at a high rate of descent, coming to rest in the grass adjacent to runway. The helicopter sustained substantial damage to the fuselage, main rotor system, and tail rotor system. A postaccident examination of the helicotper found one of the two bolts that secured the tail rotor pitch change lever assembly was missing. The lever assembly was disconnected from the trunnion, resulting in the loss of tail rotor control. The other bolt that connected the levers to the rod assembly was in place, but loose; the cotter pin for its attachment nut was missing. A review of the maintenance records revealed that a 300 hour/3 month inspection was performed on the helicopter about 15.4 flight hours before the accident. According to the helicopter manufacturer, that recent inspection would not have required removal of the lever assembly bolts; however, the nuts and bolts should have been clearly visible during the inspection of the area. The mechanic who performed the inspection stated that he must have overlooked them.

Full narrative

On August 1, 2023, about 1530 eastern daylight time, a Bell Helicopter Textron Canada 407, N31PB, was substantially damaged when it was involved in an accident near North Charleston, South Carolina. The commercial pilot sustained minor injuries. The helicopter was operated as a public aircraft.

The helicopter, operated by the Charleston County Sheriff’s Office, was on a positioning flight from Sumter Airport (SMS), Sumter, South Carolina, to Charleston AFB International Airport (CHS), North Charleston, South Carolina. The pilot reported that, after about 35 minutes of flight, the helicopter started to yaw slowly to the right. The pilot applied left pedal with no response. The pilot stated, “It felt as if the pedals were not attached.” He contacted CHS tower and declared an emergency. He set up for a straight-in approach to runway 15. While crossing the runway threshold, about 20 ft above ground level, the helicopter started to yaw to the right. He lowered the collective, but the helicopter continued to yaw right. He then reduced the throttle and attempted to maintain a level attitude. The helicopter struck the ground adjacent to runway 15 at a high rate of descent, coming to rest in the grass. The tail rotor boom severed during the impact sequence.

Inspectors with the Federal Aviation Administration (FAA) responded to the accident site and examined the wreckage. They confirmed substantial damage to the fuselage, main rotor system, and tail rotor system. They found 1 of the 2 bolts that secured the tail rotor pitch change lever assembly was missing (Photo 1). The lever assembly was disconnected from the trunnion. The other bolt that connected the levers to the rod assembly was in place, but loose; the cotter pin for its attachment nut was missing (Photo 2).

Photo 1: Tail rotor Pitch Change Lever Assembly. Red arrow points to area of missing bolt.

Photo 2: Pitch Change Lever Assembly. Red arrow points to loose nut on bolt; cotter pin was missing.

A review of the maintenance records by FAA inspectors revealed that a 300 hour/3 month inspection was performed on the helicopter on June 28, 2023. The helicopter had been flown about 15.4 hours since this inspection. According to Bell Helicopter technical support personnel, the inspection/lubrication procedure that was accomplished on June 28 would not require removal of the lever assembly bolts; however, the nuts and bolts should have been clearly visible during the inspection of the area. The mechanic who performed the inspection stated that he must have overlooked them.

Probable cause

A failure of the tail rotor pitch change lever assembly due to incorrectly installed bolts and maintenance personnel’s inadequate inspection of the tail rotor control system. The National Transportation Safety Board determined the probable cause of this accident.

Circumstances

Event type
Accident
Highest injury
Minor
Weather conditions
Visual Meteorological Cond
Light condition
Day
Sky condition
BKN
Ceiling (ft)
5500
Visibility (sm)
10
Wind direction
110
Wind speed (kt)
9
Temperature (F)
88
Nearest airport
Charleston AFB International
Distance from field
0.0
Airport elevation
46

Aircraft

RegistrationMakeModelDamageFAR part
N31PB BELL HELICOPTER TEXTRON CANADA 407 SUBS PUBU

Sequence of events

#OccurrencePhase
1 Approach-VFR pattern final Flight control sys malf/fail defining Cruise
3 Landing Hard landing Cruise

Findings

Finding
Aircraft-Aircraft systems-Flight control system-(general)-Inadequate inspection cause
Personnel issues-Task performance-Inspection-Scheduled/routine inspection-Maintenance personnel cause
Personnel issues-Task performance-Maintenance-(general)-Maintenance personnel cause