N1157G Mooney M20K accident

NTSB FTW00LA068 · 2000-01-19 · TYLER, TX

Docket — crew, injuries and powerplant

Summary

The pilot reported that the engine lost total power while in cruise flight between 1,500 feet and 2,000 feet agl. He executed a forced landing, during which the airplane contacted a fence post. During the postaccident examination of the engine, the crankshaft drive gear was observed fractured. Three consecutive gear teeth of the crankshaft drive gear separated, of which two were recovered. The crankshaft drive gear and gear teeth were examined at the NTSB Materials Laboratory and three areas of fatigue were observed. Each fatigue area originated at the relief radius at the root of one of the three separated teeth. No tooling marks or gouge marks were observed near the fracture surface or on the remainder of the crankshaft gear's teeth. The outermost nitrided layer of the crankshaft drive gear appeared smooth and no cracks were noted. Additionally, machining marks through the entire crankshaft drive gear appeared consistent.

Full narrative

On January 19, 2000, at 1230 central standard time, a Mooney M20K, N1157G, was substantially damaged during a forced landing following a loss of engine power near Tyler, Texas. The private pilot, who was the registered owner and sole occupant of the airplane, was not injured. Visual meteorological conditions prevailed for the 14 Code of Federal Regulations Part 91 personal flight and a flight plan was not filed. The cross-country flight departed from the Addison Airport, Addison, Texas, approximately 1155, and was destined for the Tyler Pounds Field, Tyler, Texas.

According to the pilot, he was flying between 1,500 and 2,000 feet agl and was 10 miles from the Tyler Pounds Airport when the "engine rpm gradually decreased," and the engine lost total power. He switched the fuel selector from the left tank to the right tank and attempted to re-start the engine, but was unsuccessful. He then initiated a forced landing to a field. During the landing roll, the left wing contacted a 6"X6" wood fence post, damaging the wing spar, and the airplane came to a stop upright 6.5 miles from the Tyler Pounds Airport.

The 210-horsepower Continental TSIO-360-LB1 engine was examined by an FAA inspector and a representative from Teledyne Continental Motors. During the examination they removed the rear accessory case cover and observed that the crankshaft drive gear was fractured. Three consecutive teeth of the crankshaft drive gear separated. Two of the three teeth were recovered.

The NTSB Investigator-In-Charge and an NTSB Metallurgist examined the fractured crankshaft drive gear and gear teeth at the NTSB Materials Laboratory in Washington D.C. Three areas of fatigue were observed. Each fatigue area originated at the relief radius at the root of one of the three consecutive teeth of the crankshaft drive gear that separated. No tooling marks or gouge marks were observed near the fracture surfaces or on the remainder of the crankshaft gear teeth. The outermost nitrided layer of the crankshaft drive gear appeared smooth and no cracks were noted. Additionally, machining marks through the entire crankshaft drive gear appeared consistent.

Probable cause

The failure of the crankshaft drive gear as a result of fatigue, which resulted in a forced landing. A factor was the lack of suitable terrain for the forced landing. The National Transportation Safety Board determined the probable cause of this accident.

Circumstances

Event type
Accident
Highest injury
None
Weather conditions
Visual Meteorological Cond
Light condition
Day
Sky condition
NONE
Ceiling (ft)
0
Visibility (sm)
7
Wind direction
200
Wind speed (kt)
7
Temperature (F)
55
Distance from field
0.0

Aircraft

RegistrationMakeModelDamageFAR part
N1157G Mooney M20K SUBS 091

Sequence of events

#OccurrencePhase
1 351 Cruise
2 180 Cruise
3 310 Cruise

Findings

Finding
14023 cause
14023 cause
20200
19200 factor