N9876A Cessna 195 accident

NTSB FTW00LA160 · 2000-05-28 · KAUFMAN, TX · near K00

Docket — crew, injuries and powerplant

Summary

According to the pilot, 20 minutes after departure, while in cruise flight, the airplane's engine began to 'run rough' and vibrate. He reduced power in attempts to dampen the vibration and initiated a precautionary landing to a nearby airport. As the airplane touched down the pilot noticed a dirt embankment, which was approximately 2 feet high, running along the runway centerline. Subsequently, the airplane contacted the embankment, exited the runway surface, struck a fence and trees, and came to a stop upright. A test run of the engine revealed that the engine would not run with the ignition switch in the LEFT position, and would run rough in the BOTH position. Examination of the left magneto revealed that the resistance was less than 16,000 ohms, failing to meet the manufacturer's specifications. Additionally, the number 3, 4, and 5 rear spark plugs exhibited oil and lead deposits.

Full narrative

On May 28, 2000, at 0930 central daylight time, a Cessna 195 tailwheel equipped airplane, N9876A, was substantially damaged during a precautionary landing following a partial loss of engine power near Kaufman, Texas. The airline transport rated pilot, who was the registered owner and sole occupant of the airplane, sustained minor injuries. Visual meteorological conditions prevailed for the 14 Code of Federal Regulations Part 91 personal flight and no flight plan was filed. The cross-country flight originated from the Aero Country Airport, McKinney, Texas, at 0900 and was destined for Galveston, Texas.

The pilot reported that 20 minutes after departure, while in cruise flight, the engine began to "run rough" and vibrate. He reduced power in attempts to dampen the vibration. He initiated a precautionary landing to the Hall Airport, Kaufman, Texas. The pilot stated that as he landed on runway 17 he noticed a dirt embankment that was approximately 2 feet high running along the runway centerline. Subsequently, the airplane contacted the embankment and departed the left side of the runway. The airplane impacted trees and a fence, and came to a stop upright. The pilot stated that there was an "X" made out of PVC pipe at the end of the runway; however, he did not see the "X" prior to landing as it was obscured by tall grass.

An FAA inspector, who examined the airplane, stated that the main landing gear were collapsed, and the fuselage sustained structural damage.

The 300-horsepower Jacobs radial engine was test run in the presence of an FAA inspector. It took three attempts to start the engine. The engine ran rough with the ignition switch in the BOTH position, and when the ignition was switched to the LEFT position, the engine began to lose power. The ignition was switched back to BOTH, and the engine continued to run rough. The ignition switch was switched a second time to the LEFT position, and the engine started to lose power again. A continuity check was performed on the left magneto and it did not meet the manufacturer's specifications (resistance was less than the required 16,000 ohms). Additionally, the number 3, 4, and 5 rear spark plugs exhibited oil and lead deposits.

Probable cause

The failure of the left magneto, which resulted in a partial loss of engine power. Factors were the fouled number 3, 4, and 5 rear spark plugs and the lack of suitable terrain for the precautionary landing. The National Transportation Safety Board determined the probable cause of this accident.

Circumstances

Event type
Accident
Highest injury
Minor
Weather conditions
Visual Meteorological Cond
Light condition
Day
Sky condition
NONE
Ceiling (ft)
0
Visibility (sm)
5
Wind direction
190
Wind speed (kt)
10
Temperature (F)
79
Nearest airport
HALL AIRPORT
Distance from field
0.0
Airport elevation
440

Aircraft

RegistrationMakeModelDamageFAR part
N9876A Cessna 195 SUBS 091

Sequence of events

#OccurrencePhase
1 352 Cruise
2 320 Cruise

Findings

Finding
14801 cause
14803 factor
24546
19200 factor